![]() Relief: When connecting the cable to the camera, you MUST provide some type of strain relief so the cable is not pulling on the connection especially at the camera end, otherwise you will damage the pins in the connector Grey Connector on the cable into the remote. Plug the Black Connector on the cable into the camera. If you power off the camera, you will need to follow these instructions again. Status on the external LCD Monitor via the HDMI jack. The > icon AND DO NOT PRESS any other buttons.ĭo NOT turn the camera off, just plug in the cable for the external LCD monitor.Īs long as you leave the camera on and in this setting, you will have the Record Scroll across to the arrow icon, it looks like this > You will see Icons on the bottom of the screen. ![]() ![]() Then continue scrolling down to “Scene Selection” andĦ. Scroll down to “Low Lux” and make sure it is set to OFFĥ. Instructions on how to see the Record Status and Battery Indicator on the External LCD Monitor when connected via the HDMI jack.ģ. They are made with the 15 pin connector that Sony uses for the MultiportĬonnection on the video camera and the remote control.Īll Cables are Tested with a Sony RM-VPR1 and a Sony HDR CX440 camcorder prior to shipping. NOTE: While they may look like a USB cable they are NOT. This cable is also called a Sony Multiport extension cable, Sony Multi Terminal Cable or a Sony Multiport replacement cable. I am sorry but we will NOT cover damage like this under the warranty, since this is caused by the end user. As an example, you might try looping the cable around the camera strap before plugging it into the camera. NOTE: When connecting the cable to the camera, you MUST provide some type of strain relief so the cable is not pulling on the connection especially at the camera end, otherwise you will damage the pins in the connector If the remote will not control the camera, then power off the cameraĪnd unplug and replug in both ends of the cable. Please make sure the cable is plugged in all the way. When you plug the cable in, you should hear Make sure you are plugging the cable in the correct way, or you may damage the connector. The serial number is needed for your warranty.) (NOTE: Do NOT remove the label as it also has the serial number for the cable on the We have a label on the cable to remind you Next, the Grey end of the cable plugs into the remote and the Black end plugs into the camera. Unplug the cable that came with the the Sony RM-VPR1 or VCT-VPR1 remote controller, as you will be replacing that cable with Power the camera OFF when plugging in or unplugging the cable. That the connectors are very small and fragile and they must handle them with care. PLEASE warn who ever is setting up and working with the End Zone Camera equipment, Your camera MUST have a Multiport Connection like shown above.Īttention Coaches: While this cable is heavy duty and is perfect for End Zone and Sideline camera setups. These extension cables are perfect for use with End Zone camera and Sideline camera setups. Why Sony went to this type of small fragile connector is beyond me, but you need to They are very tiny and will damage if you are not careful with them. NOTE: YOU MUST be careful with the connectors as cable weights one pound as it is a very thick cable, plus it isĬompletely shielded. They are heavy duty and made with heavy gauge wires so there will not be any signal loss between the remote and the cameras. These cables have a male Multiport connector on both ends, allowing you to extend the distances between the remote and the camera.įour lengths, 12 ft., 18 ft., 27 ft. The extension or replacement cables on this page are only for the Sony brand, the JJC SR-F2 and the Revo VRS-Multi remote controllers allow the cable to be unplugged at the remote control unit and replaced with our longer cable. Other 3rd party or aftermarket controllers do not allow the cable to be replaced, as they are hardwired in. Replacement cables for these two controllers. If you have a JJC SR-F2 remote or the Revo VRS-Multi remote, we do have extension / Units, which are the Sony RM-VPR1 and the Sony VCT-VPR1 tripod remotes. These cables only work with the Sony Brand Remote Control All Cables are tested at the factory and at Studio 1 Productions with a Sony RM-VPR1Īnd a Sony HDR CX440 camcorder prior to shipping.
0 Comments
Leave a Reply. |